Jump to content

Charged VR

Members
  • Content Count

    235
  • Joined

  • Last visited

Everything posted by Charged VR

  1. Id second that, Take the water pump out and check the fins, When i did my rebuild my old pump only had 3 fins left Get it sorted soon though so it doesnt cause any major problems!!
  2. I will get you this number, But wont be able to get it until Monday
  3. I bought my from G/S/F as well,Goodridge 6 line kit, Cost me just over £50, Only bought them about 8 months ago
  4. I bought a fully primed bumper without the textured section from Euro car parts a year ago. If the data sticker is missing then you can still get the colour code from the Dealer with your Reg or Chassis Number. I work at windrush in maidenhead and can do this for you if you Pm me your reg
  5. You can get the valve on its own from VW, Its under sharan VR6 and starts with 7MO on the part number. I can get you the number if you want. I paid around £7 for mine
  6. I did the ball joints myself so it was only the price of the parts. Not difficult to do so it wouldnt be that expensive. Just make sure when the do the alingment that they check everything and not just the tracking
  7. The scuttle tray comes in two halves? Do you want a price on both? And is it just the top trim on the skirt that you need? Will try and get the numbers for you tomorrow
  8. £45 is good if it is a Full 4wheel Alignment, i work at a dealer and we charge £120 for a check!!! My VR used twitch, Replaced both lower ball joints and it drove so much better. Well worth it as they were not that expensive
  9. Have you checked the wiper stalk? Does it smell of electrical burning aroung the steering trims?
  10. I think the green wire that you are talking about is the oil temp sensor for the MFA display. Are all the connectors aroung the front engine mount connected?
  11. Well worth checking there are no Air leaks. Next to the throttle vale is a small palstic box. These can split and cause unmeterd air in and it wont idle.
  12. Have you both checked for Intake air leaks or faulty coolant temp sensors? And are your cars OBD 1 or 2?
  13. You will have a coilpack on a VR this late. Only the very early Golf VR's had a distributor but from M-N Reg thi Changed to a coil pack
  14. Do you know the fault code's? I wouldn't replace the Throttle possition sensor or the Vehicle (Engine?) speed sensor wthout testing first. Maybe something else. VR's always show engine speed sensor fault when not running with VAG Tester
  15. Most Car Locksmith should be able to cut and code the key. The one that i use never has a problem
  16. Thats the best way mate, Make sure you clean the hole out before you fit the new one so that it fits flush and nicley
  17. Dubpowr leads are Realy good and they do a set of standard red leads for around £40.
  18. They are your oil preesure sensors and there is also a temp sensor there for the mfa. Usual problem with them splitting in the centre and leaking. Not much from vw, just need to know what colour for what pressure sensor it is
  19. Revotec do a 52mm gauge with supercharger on the face instead of the usual Turbo or Boost. Expensive gauge compared to some but is realy good quality
  20. Followed the bonnet cable on mine through the bulkhead and into the car. Sealed the end. Perfect
  21. Just thought it was something different for a change and its still good old Vdub!!
  22. Just a quick picture of the girlfriends beetle Must be room for a VR lump in there somewhere?
  23. Yes mate, Just fineshed my mates VR and i fitted front rear black diamond disc's and they are top notch. Do you want coilovers or springs-struts?
×
×
  • Create New...