jellsta 0 Posted July 23, 2006 Report Share Posted July 23, 2006 Hi there want to remove my plastic arches, but am left with a gap and a hole where the vr6 side srip ends. any ideas how to comabt this?? cheers :-d Link to post Share on other sites
Earwig 89 Posted July 23, 2006 Report Share Posted July 23, 2006 Have it smoothed over? Only real way to get rid of a hole :-)Mark. Link to post Share on other sites
dubloke 4 Posted July 23, 2006 Report Share Posted July 23, 2006 or get some cl side strips which cover the holes with standard trim! Link to post Share on other sites
jellsta 0 Posted July 23, 2006 Author Report Share Posted July 23, 2006 cl trim sounds a better idea, any idea where i can get some cheap? cheers Link to post Share on other sites
antera309 3 Posted July 23, 2006 Report Share Posted July 23, 2006 You don't need to replace all your existing side strips with the ones from a CL. All you need are the ones that go on the rear quarter panels. The CL ones are 63mm long, as opposed to the 53mm ones you have. Euro Car Parts do 'em. Link to post Share on other sites
mike 6 Posted July 23, 2006 Report Share Posted July 23, 2006 i found CL trim didnt match up tho, didnt have the line going thru iyt like the VR trim, i can get a full CL set for £25 (scrappy) Some places charge £100 plus Link to post Share on other sites
richievr 1 Posted July 24, 2006 Report Share Posted July 24, 2006 You don't need to replace all your existing side strips with the ones from a CL. All you need are the ones that go on the rear quarter panels. The CL ones are 63mm long' date=' as opposed to the 53mm ones you have. Euro Car Parts do 'em.[/quote']unfortunately yes you do (i have done mine)the gti/vr6 ones are deeper than the cl ones and have a stripe down them ..if you change just the rear quarter panel ones it look wrong ... :-( :-( Link to post Share on other sites
mike 6 Posted August 5, 2006 Report Share Posted August 5, 2006 as richie says you need the full set, (which i can get cheap) Link to post Share on other sites
gav_113 0 Posted August 5, 2006 Report Share Posted August 5, 2006 i replaced mine with colour coded ones from a highline, i think VW wanted about £180 for a complete set :@ got mine on ebay £40 Link to post Share on other sites
vr6turbo 27 Posted August 18, 2006 Report Share Posted August 18, 2006 i agree i have had the same trouble as the car is in the paint shop and have taken off the wheel arch trims (as requested)i need a cl 3 door set because of the difference in depthbetween the vr and the cl side trimsyou can refit the vr6 side badges on to the cl trims, with a bit of work Link to post Share on other sites
VR6chris 0 Posted August 23, 2006 Report Share Posted August 23, 2006 A detrimed mine with cl trim for a fiver just your luck. the two are defo diffrent and remmbert to keep the clips from both the trims coz you brake most of the clips when you take them off. Link to post Share on other sites
dscam 0 Posted September 13, 2006 Report Share Posted September 13, 2006 Hi guys,Just to clarify then: If I remove the arches from my 5dr VR6 I'll be left with gaps in the side strips where they meet the arches?I see the point about getting CL trim to replace but does the highline stuff look better?Cheers,Duncan Link to post Share on other sites
dscam 0 Posted October 13, 2006 Report Share Posted October 13, 2006 ^bump^ Link to post Share on other sites
Recommended Posts