Jump to content

madmonkee

Members
 View Profile  See their activity

  • Content Count

    410

  • Joined

  • Last visited

 Content Type 

Everything posted by madmonkee

  1. madmonkee
    looks tidy m8ty
  2. madmonkee
    lol ai bit cramped tho en it!?
  3. madmonkee

    leds....

    madmonkee replied to madmonkee's topic in Interior

    all done all blue and working all i need now is some more money to buy a few more bits
  4. madmonkee
    reasons not to use dot 5, conclusive really.... read on, Silicone DOT 5 is not compatible with the ABS hydraulic control unit because it doesn't lubricate the ABS pump like glycol based fluid. Silicone is slightly more compressible than glycol fluid. It has a higher wet boiling point because it doesn't absorb moisture like glycol fluid. This lack of moisture absorption causes problems when water gets in the brake system. Instead of mixing with the brake fluid (so it can be flushed out easily), the moisture gets trapped at low points in the system and causes rust.
  5. madmonkee
    nope, abd1 m8ty good ole orriginal VR6 material in da house. 92K plater
  6. madmonkee
    its not gonna be permanent, the one in the front will be, but as said, it will be for shows, it will hide the bit of my install i really havent finished. Just something to look at really. Once i go home take it back out, untill the next show
  7. madmonkee
    After you have the cluster bare to where you can physically touch the needles, grab two small flat head screwdrivers. wedge the screwdrivers under the round base of the needle (one at 3 o clock and the other at 9 o clock) and VERY CAREFULLY push down on the screwdrivers, wedging the needles out. Make sure that you apply the same force to both sides or you will pull out the spring.
  8. madmonkee
    but as for always spending money on it i know how that feels..... my latest bill is £500
  9. madmonkee
    no not the gti-6 get the rally if you can. Same engine as gti-6 but alot lighter
  10. madmonkee
    ill go for that too
  11. madmonkee
    fun sport, or fun tech are the ones to get apparantly. Basically they are the K+W's old line of suspension. There new stuff is well expensive, Inox line (like ive got) but ive been told these are the boy for less than £400
  12. madmonkee
    i have a539's on mine and they are crap!!!! Eagle f1's all the way baby, they stick like shite to a blanket, in wet an in the dry. but dont last to long mind u
  13. madmonkee
    could be as simple as low tire pressure matey.
  14. madmonkee
    yes i am! It was a toss up between 76 dot 5 at £23 a bottle(just under 1ltr) or £45 for the castrol SRF. We struck a deal, he said he would put the castrol in, but charge me the £23 for if i was buying the 76. Also it has been known for me to be braking from about 5000rpm in 5th very rapidly...... car doesnt stop
  15. madmonkee
    im gonna mount a screen in the gear stick bit, also one in the boot to finish off me install. Wat size screen will fit in the gap below the heater controls?? Havent really looked.
  16. madmonkee

    New alloys

    madmonkee replied to bazz780's topic in General Chat

    ^^^^^^^ agreed with that, mine was more than £70 to have fitted. I had all that jazz done.
  17. madmonkee
    nope, £123 for discs 8 grooved £43 pads fast road rally. £41 wheel bearing kit x2 £60 hoses BF Goodrich £45 dot 4 castrol srf brake fluid. £353 for materials £142 labour, If the hoses come off without fookin up. not bad really wat u think? £495 total [ Edited Mon Aug 09 2004, 10:46PM ] [ Edited Mon Aug 09 2004, 10:51PM ]
  18. madmonkee
    se woulda been gulping in awe of the size of me machinery
  19. madmonkee
    tiny tweaters, but you can fit a 4" speaker in there sweet as, Doors (for 5 door) is front 6.1/2" speakers with tweaters in the dash. Rear doors the same 6.1/2 in the door with tweaters in the handle, all easy as to change. Boot you can ram full of big ole speakers...... BOOOOM shaka la!
  20. madmonkee
    Pagid fast road/rally discs (frontx2) pagid fast road rally pads (front only) braided hoses (6 piece kit) Front wheel bearings (because mine are fucked, thats the noise and the wheel is about to fall off!!!) Castrol Dot 5 brake fluid(just under a litre) Labour charges ontop?
  21. madmonkee

    Rusty VR's

    madmonkee replied to Coddy's topic in General Chat

    mines above windscreen, rear hatch (bottom of the glass) edge of passenger front an passenger rear door around the rubber grommet below the catch.... apart from that not bad for K plater
  22. madmonkee
    yes wet as well she was just scared me thinks. Phsyco monkee boy on her case
  23. madmonkee
    Behind me all the way home, driving steady, the road opens up into two lanes at the traffic lights, she goes past me (still going steady) then she cuts across in front of me as the next set change to red...... GRRRR. "cut me up hey" Then, zooms in next to me a Renault megane RT, with bird driving, gives me the look "she wanna play " Eyes lookin in the rear mirror at me s2000 bird, "she wants a piece too" Me is thinking "s2000 is v.nippy..... agh fuck it ill give her a portion!" Lights change s2000 pulls away steady, into 2nd SCREEEEEECH RT bird trying it on wheel spinning like a pleb, s
  24. madmonkee
    is it just a pressure fit?? how did u make sure that yours are properly calibrated?? if i let the neddle drop down as far as it goes till it stops, is that true 0 mph?? they look the boy btw
  25. madmonkee
    no they just look like mrk4 dials. Olly m8ty, you have drop down dials, my new dials start at 0, not 10 as my orriginal do. How do i get the needle off and reset them so that they start at 0. If i put the needle over the stop needle the distance it drops down is about the same distance from 10-20. So I was thinking about letting the needle drop right down, pulling it off and puttin it back on over the otherside of the needle stop. So it would be reading 0. (or ten on my orriginal dials)
×
×
  • Create New...