jims13 6 Posted March 26, 2007 Report Share Posted March 26, 2007 right i seem to have these faults, the abs one's i new about, and the maf, i assumed was because the car was not running... update, had another look, evap purge valve is disconnected so thats why it registered a fault. the one im intrested in is the lamdba sensor...does it need changing, i have no cat but ,the sensor is still in there.Chassis Type: 1H - VW G/J/V Mk3Scan: 01,02,03,08,15,25,56-------------------------------------------------------------------------------Address 01: Engine Controller: 021 906 256 Component: MOTRONIC M3.8.1 HS V04 Coding: 00000 Shop #: WSC 013195 Faults Found:00668 - Supply Voltage Terminal 30 07-10 - Signal too Low - Intermittent01247 00553 00525 - Oxygen Sensor (G39) 03-10 - No Signal - Intermittent00635 - Readiness: N/A-------------------------------------------------------------------------------Address 03: ABS Brakes Controller: 3A0 907 379 E Component: ABS/EDS ITTAE 20 GI V00 Coding: 03704 Shop #: WSC 000003 Faults Found:00290 - ABS Wheel Speed Sensor: Rear Left (G46) 35-10 - - - Intermittent00287 00287 Link to post Share on other sites
cabrioman 6 Posted March 26, 2007 Report Share Posted March 26, 2007 well as it sayin no sifnal it could be a broken wire or a dodgy sensor, i left my sensor in when i de catted but it was readin a lean value so ther ewas no fault with it put the car back on adn now all good Link to post Share on other sites
VR6_Absy 0 Posted March 26, 2007 Report Share Posted March 26, 2007 Clear the codes individually and then re-run but you must have the engine running or it will return faults Link to post Share on other sites
jims13 6 Posted March 26, 2007 Author Report Share Posted March 26, 2007 ah, i thought you had to run it with the car in ign pos 2.. Link to post Share on other sites
VR6_Absy 0 Posted March 26, 2007 Report Share Posted March 26, 2007 ;-) Link to post Share on other sites
VR6Rich 3 Posted March 26, 2007 Report Share Posted March 26, 2007 You don't need the engine running at all, just need the ignition on thats all. Link to post Share on other sites
jims13 6 Posted March 26, 2007 Author Report Share Posted March 26, 2007 Well i have some lambda's kicking around , ill change it over and try it again, after i cleared the faults. Link to post Share on other sites
Earwig 89 Posted March 27, 2007 Report Share Posted March 27, 2007 Hope your gonna get the ABS done before you go... ;-)Mark. Link to post Share on other sites
VR6_Absy 0 Posted March 27, 2007 Report Share Posted March 27, 2007 I get faults if the engine isn't running, can't remember which ones exactly but similar to Jim Link to post Share on other sites
jims13 6 Posted March 27, 2007 Author Report Share Posted March 27, 2007 Mark, i wont have tim eto get the abs sorted, so im gonna pull the fuse and run without.... eek ! Link to post Share on other sites
Earwig 89 Posted March 29, 2007 Report Share Posted March 29, 2007 Sounds fun !My ABS is hopefully being sorted at the moment :-)Mark. Link to post Share on other sites
jims13 6 Posted March 29, 2007 Author Report Share Posted March 29, 2007 SORTED the lambda, it was a broken wire on the plug , i only noticed it when i went to move the plug.all is well now and the car made 199.7 bhp at the rr today Link to post Share on other sites
Recommended Posts